16 T1/E1 Fiber Optical Multiplexer
Product ID: Fox-F
Fox-F, Fiber Optic Multiplexer (FOM), provides the electrical to optical conversion of electronic communication and data signals. Fox-F simultaneously transmits and receives optical signals through optical fiber, and converts them back to original electrical signal in full duplex transmission.
Designed as a single unit (1U), 19"/23"rack mountable, 4 slots of a modular design at the rear of the chassis, Fox-F can either be equipped with T1/ E1, V.35, or Ethernet cards and may extend the service range up to 100 KM over fiber optic cable.
- Aggregate Optical module specification
- Source: MLM Laser
- Wavelength: 1310 nm*
- System gain: >19 dB**(@ 1x10^10 BER)
- Protection: 1+1 APS
- Switching time: ≤ 50ms
- Connector: FC/PC or SC/PC
- *1550nm can be provided upon request
- **System gain > 20 and 25dB are also available upon request
- E1 specification:
- Port number: 4 ports per module (up to 16xE1)
- Standards: ITU-T G.703, G.704
- Data rate: 2.048 Mbps
- Line Code: HDB3
- Line impedance: 75 Ohm/120 Ohm
- Connector: DB25 for 120 Ohm, BNC for 75 Ohm, or Wire-Wrap
- T1 specification:
- Port number: 4 ports per module (up to 16xT1)
- Standards: ITU-T G.703, G.704
- Data rate: 1.544 Mbps
- Line Code: B8ZS, AMI
- Line impedance: 100 Ohm
- Connector: DB25 for 120 Ohm, BNC for 75 Ohm , or Wire-Wrap
- Ethernet specification:
- Port number: 1 ports per module (up to 4xEthernet)
- Standards: IEEE 802.3/802.3u
- Connector: Shielded RJ-45
- Filtering and Forwarding: WAN speed
- WAN Protocol: HDLC
- V.35 (Datacom) specification:
- Port number: 4 ports per module (up to 16xV.35)
- Data rate: n x 64K, n = 1 to 32
- Line Code: NRZ
- Clock Mode: Transparent, Recovery, External (Data port) or Internal
- Test Loops: Local loop back, Remote loop back, V.54
- Connector Type: Female 34pin with adapter cables
- Power Supply:
- DC: -48VDC
- AC: 110/220VAC @ 50/60Hz
- Power Consumption: ≤ 25W
- Operation Environmental Conditions:
- Temperature: 0 ~ 60ºC; 32 ~ 140ºF
- Humidity: Up to 95% (non-condensing)
- Mechanical Specification:
- Height x Width x Depth: 45 x 440 x 300 mm
- EMI/EMC/Safety:
- EMI: FCC, Part 15, Sub B (Class A)
- CISPR22 Class A
- Channel Capacity: Up to 16xE1/T1, 16xV.35, or 4xEthernet
- Redundant fiber 1+1 protection
- Remote control function
- Local and remote Loop-Back function
- Single mode/multi-mode fiber connection
- Optical and channel modules are hot swappable
- Configuration data can be stored into flash memory and Critical/ major/ minor alarms relay with audible and visible output
- Modularized design interface:
- G.703 E1 and T1
- G.704 E1 and T1
- Datacom (V.35)
- Ethernet
- Network Management System interface:
- LCD panel with Keypads
- CIT port with RS-232
- OS (LAN) port with SNMP
Main Products:
MDSL-Digital Pair Gain System, Digital Added Main Line System, ISDN Internet Card