FlexRay Communications Expansion Kit for LE-8200-E
Product ID: OP-SB88
The FlexRay communication is anticipated as a next-generation high-speed in-vehicle network.
The OP-SB88 is an expansion kit that allows monitoring of FlexRay communications on up to two channels in real time.
The kit incorporates a monitor function that does not require complicated parameter settings, and a simulation function with which the OP-SB88 works as a FlexRay communications node to transmit and receive data, thus powerfully supporting the initial development.
The filter function and high-capacity memory greatly shorten the analysis time of trouble.
Furthermore, it incorporates a simultaneous measurement function for external signals, which makes it possible to investigate the relationship between the operation of peripheral devices and communications data.
- Features
- 10Mbps, 5Mbps, 2.5Mbps Communication Speed
- Easy Monitoring
- Dual Controller
- FlexRay Transceiver, TJA1080
- Monitor Function
- Reception Filter for Each Channel
- Simultaneous Measurement of External Signal
- Display Specific Data on Pointed Line
- Event Counter Display
- Trigger Function
- Simulation Funcition
- Automatic Frame Transmission
- Event Transmission of Frame
- File Saving
- Print Function
- Technical Support
| Protocol | FlaxRay V2.1A |
|---|---|
| Transceiver | TJA1080 or RS-485 ( equivalent to SN65HVD3088E ) selectable from the analyzer |
| Measured Channel | 2 channels (A and B) |
| Speed | 10Mbps, 5Mbps, 2.5Mbps A/B channel |
| Monitor Function | Saves FlexRay data per frame. isplays following objects on several kinds of mode :Header/ Payload(0 to 254 bytes) / Trailer Segment , CAS Symbol |
| Error Check | Header CRC error/ Frame CRC Error, It is possible to display CRC value |
| Time Stamp | 9 digits. Diaplays the time between the start of measuement and the point of receiving a frame, or the time between the received frames in 1mS or 100μS or 10μS or 1μS unit. |
| Capture Memory | Capacity : 100MB (Data is saved to the capturing memory of the analyzer.) Data can be used as ring buffer or fixed size buffer. |
| Auto Save Function | Automatically saves the monitored data as communications log file in the CF card. |
| Display format | Frame display, Payload display, External signal voltage display, Display specified frames at the fixed position |
| Counter function | Counts trigger conditions, received frame, Header CRC error and Frame CRC error (max. 6 digits). |
| Filter Function | Saves/displays only the specific frames matched with following conditions :Each bit of channel or indicator, specific ID, specific cycle counter |
| Trigger Function | Automatically stops measuring when the following conditions are found. Data (6 sets) : Appointment Channel, Indisator, ID, Cycle Counter, specific Payload Data in the frame(max.16 data, Don't care and Bitmask can be selected). Error (1 set) : Header CRC Error / Frame CRC Error. External Input (1 set) : The falling edge of the extrernal trigger input |
| Simulation Function | Can transmit the data registered previously or the presetting data. Can transmit the startup fame or the synchronous frame(up to 2 nodes). Can point the preamble indicator. Can transmit the wakeup symbol (WUS). |
| Transmitting Payload | Data length : 0 to 254 bytes. Max. 784 kinds of transmitting Payload can be registered. |
| Continuous transmission | Up to 16 kinds of data can continuously send. Data is with Channel, ID, Cycle counter and Payload (It is possible that a part of the data can automatically sweep at the designated condition). Or data with Channel, ID and Pattern (selected from at most 8 patterns that are designated the Payload per communication cycle). |
| Event Transmission | Can transmit registered frames by the key operation. (continuously or one-shot). The frames include the data of Channel, ID, Cycle counter. Up to 16 kinds of frames can be resigted and each one has 8 kinds of Payload. |
| External Signal Input | Measures the logic conditions and voltate (range: -15 to +15V) of Input of four external signals (max. input: -25 to +25V) on the timing of receiving frames, and saves it to the memory with the frame data. Also displays it on the LCD / LEDs at real-time. |
| External Trigger input/output | Input of external trigger: 1, Output of external trigger: 1, Both on TTL level |
| Componets | Expansion board, Firmware CD, Line state sheet(B), Two DB9 monitor cables, Two 3-line-probe cable, 8-line-probe cable |
Main Products:
Multi Protocol Analyzer, USB Protocol Analyzer, LAN Analyzer
Contact Details
Sales Contact: Ms. Fujii
Minimum Order:Negotiable
Address:39-1, Karahashi, Nishihiragaki-cho, Minami-ku Kyoto, 601-8468 Japan
Tel:81-75-693-0161
Fax:81-75-693-0163