interface converter
E1-Ethernet Interface Converter
Item No.: GE-01
E1-Ethernet Interface Converter Description
E1 to Ethernet Interface Converter is also called E1 to Ethernet protocol converter or E1 to Ethernet bridge. The E1 to 10/100Base-T serial interface converter used back multiplexing technology, transfer 10M/100M Ethernet data by using multi E1 channels. Realize convert between E1 channel and Ethernet interface. It can transmit signal of E1 channel to RJ45 interface point to point, realize the connection of E1 channel and Ethernet. It is different from normal bridge, supporting E1 channel customized configuration, auto detecting the number of E1 channels and use the available E1, allow some limiting transfer delay between different E1 channels. Single line speed is 1968Kbits/s. It can connect with Ethernet switch or hub when in 10/100Mbps full/half duplex mode, make use of mass E1 resource in telecommunication networks to expend the transfer distance and application field of Ethernet, is a suitable solution for broadband switch in of Ethernet. It can used in fields such as connecting LANs, connecting end offices, VOD, remote monitor, E1 interface of switches, etc. E1 to Ethernet Interface Converter Features
- Realize transparent transfer ethernet data in x to xE1 channels
- 10/100M Ethernet, full/half duplex self adapt, support VLAN
- Ethernet support AUTO-MDIX( cross over and straight through self adapt) setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction
- When one direction error rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions
- Allow xE1 channels up to 10ms transfer delay. When the delay over the limitation, can stop transfer automatically
- Having 2 loop back functions: E1 local loop, E1 external loop
- Support dynamic ethernet MAC address (4096), having local address filter function
- E1 interface compatible with ITU-T G.703, and G.823. Signaling slot not supported
- E1 interface having internal clock resume circuit and HDB3 codec circuit
- Support E1 channel hot plug, and auto-detect available E1 channels not pause the transmission
- Supporting x to xE1 channels customized configuration, auto detect the number of E1 channels and select the available E1 at reset
- Support reset remote system from local system
- Having Ethernet monitor auto reset function
E1 to Ethernet Interface Converter Technical Specifications
E1 Interface
Connector: BNC (Q9)
Impedance: 75ohm unbalanced/ 120ohm balanced
Line Code: HDB3
Bit rate and tolerance: 2.048Mbit/s±50ppm
Standard: ITU-T G.823, G.703, G.704
Ethernet Interface
Connector: UTP RJ45
Connector Rate: 10/100M, full/half duplex auto-negotiation, auto-mdi/mdix
Max Frame Size: 1552Byte
Compliance with IEEE-802.3u, IEEE-802.1Q
Other Parameters
Input Voltage: AC100V~260V/50~60Hz, DC-36~72V
Whole Power:
Item No.: GE-01
E1-Ethernet Interface Converter Description
E1 to Ethernet Interface Converter is also called E1 to Ethernet protocol converter or E1 to Ethernet bridge. The E1 to 10/100Base-T serial interface converter used back multiplexing technology, transfer 10M/100M Ethernet data by using multi E1 channels. Realize convert between E1 channel and Ethernet interface. It can transmit signal of E1 channel to RJ45 interface point to point, realize the connection of E1 channel and Ethernet. It is different from normal bridge, supporting E1 channel customized configuration, auto detecting the number of E1 channels and use the available E1, allow some limiting transfer delay between different E1 channels. Single line speed is 1968Kbits/s. It can connect with Ethernet switch or hub when in 10/100Mbps full/half duplex mode, make use of mass E1 resource in telecommunication networks to expend the transfer distance and application field of Ethernet, is a suitable solution for broadband switch in of Ethernet. It can used in fields such as connecting LANs, connecting end offices, VOD, remote monitor, E1 interface of switches, etc. E1 to Ethernet Interface Converter Features
- Realize transparent transfer ethernet data in x to xE1 channels
- 10/100M Ethernet, full/half duplex self adapt, support VLAN
- Ethernet support AUTO-MDIX( cross over and straight through self adapt) setting CRC alarm limitation to auto isolate lines with low transfer quality, single direction
- When one direction error rate over limitation, disconnect only one direction, the other is not affected. Unbalance in two directions
- Allow xE1 channels up to 10ms transfer delay. When the delay over the limitation, can stop transfer automatically
- Having 2 loop back functions: E1 local loop, E1 external loop
- Support dynamic ethernet MAC address (4096), having local address filter function
- E1 interface compatible with ITU-T G.703, and G.823. Signaling slot not supported
- E1 interface having internal clock resume circuit and HDB3 codec circuit
- Support E1 channel hot plug, and auto-detect available E1 channels not pause the transmission
- Supporting x to xE1 channels customized configuration, auto detect the number of E1 channels and select the available E1 at reset
- Support reset remote system from local system
- Having Ethernet monitor auto reset function
E1 to Ethernet Interface Converter Technical Specifications
E1 Interface
Connector: BNC (Q9)
Impedance: 75ohm unbalanced/ 120ohm balanced
Line Code: HDB3
Bit rate and tolerance: 2.048Mbit/s±50ppm
Standard: ITU-T G.823, G.703, G.704
Ethernet Interface
Connector: UTP RJ45
Connector Rate: 10/100M, full/half duplex auto-negotiation, auto-mdi/mdix
Max Frame Size: 1552Byte
Compliance with IEEE-802.3u, IEEE-802.1Q
Other Parameters
Input Voltage: AC100V~260V/50~60Hz, DC-36~72V
Whole Power:
Certificate
- ISO9001
Main Products
fiber optic transmission,fiber optic media converter,fiber optic modem